A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
Have you been in search of details concerning How to Install a Bathtub?
Mounting a tub isn't exactly rocket science, however it does require solid plumbing, carpentry, as well as often, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably challenging project. If the old tub is readily accessible, the task can move immediately; if you have to open a wall to remove the old bathtub and also position the brand-new bathtub, the job is a lot harder. In either instance, the job is within a home handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the new one. Make certain you have actually qualified on your own for the job and fit trying it. Rather than hiring a contractor to take over a halfway-completed task, it is far better to consider employing one before you begin. Chances are you might need an expert plumber to make tube links.
This post will certainly aid you install a new bathtub in your bathroom if you have currently gotten a new bathtub and also don't require to alter the setup of your previous water pipes.
Your tools as well as product checklist must make up the following:
Planning for the Installment
To start with, the sustaining structure provided with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to prevent pressure on the bathtub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its last setting.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you must do is disconnect the water supply. After doing so, turn on the taps to drain pipes any type of water continuing to be in the system. The procedure of removing the existing taps can be rather troublesome as a result of the restricted access that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipelines. Once the supply pipelines have actually been eliminated, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Before proceeding to fit the new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Utilizing both wooden boards under its feet, put the bathtub in the needed position. The wood boards are useful in evenly spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by examining the level as well as changing the feet on the bath tub until the level reads level.
To install taps, fit the bottom of the outermost versatile tap port to the ideal supply pipeline by making a compression join; then do the very same for the other tap.
Turn on the water and check all joints and also new pipework for leaks and tighten them if needed. Fill up the bath tub as well as additionally examine the overflow electrical outlet as well as the regular electrical outlet for leakages.
Finally, fix the bathroom paneling as defined in the maker's instruction manual. Tiling and also sealing around the bath tub ought to wait until the bathtub has been used a minimum of when as this will settle it into its last placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin ensuring that the washing machines are in area in between the tap and also the sink. Protect the tap in position with the supplier given backnut. As soon as the faucet is firmly in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap ports. The previous type must be linked to the faucet finishes first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to break a rigid seal, causing the water to penetrate the wall between the bathroom as well as the tiling, causing issues with dampness and also feasible leakages to the ceiling below.
You can select from a range of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, and are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched paper or soft rope. Keep in mind to constantly fill the bathtub with water prior to securing, to allow for the movement experienced when the bathtub remains in usage. The sealer can break relatively early if you do not take into consideration this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally easily available on the market. It is recommended to fit the tiles using waterproof or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Place a short review directly below. We would be interested to see your ideas about this blog posting. We are looking forward that you visit us again before long. Enjoyed reading our post? Please share it. Help another person check it out. Many thanks for taking the time to read it.
No more waits, dial now! Report this page